20 Planning & Zoning - Laserfiche WebLink

Home Browse Search

must be completed, even if no asbestos was discovered in the survey. Example: stop work; contact owner/consultuit and DSHS; demarcate area; secure critical barriers. 9) An asbestos survey/inspection must be performed prior to any renovation or demolition. A DSHS licensed inspector must perform the inspection if the project is in a public building. Provide the DSHS Inspector License Number, if required. If the survey/inspection was perfonned in a public building prior to January 1993, or if the project is not in a public building, "N.A." should be placed in the space for the DSHS License Number. 7'he date that the survey was perfonned must be provided. The analytical method used to detect the presence of asbestos must be checked. TAfiPR requires that a DSHS licensed laboratory perform the analysis of samples from public buildings. Provide the DSHS Laboratory Number ifthe samples are collected from a public building. Ifthere was no suspect material discovered, such as a garage, built of concrete and steel only, indicate no suspect material found by the license number. The assumption of asbestos-containing building material (for renovations) in a public building must be made by a DSHS licensed inspector. The "yes" box would be checked, the date that the survey (assessment) was perfonned would be provided, the DSHS Inspector License Number would be provided, and the "assumed" analytical method boY would be checked on the notification form, for an assumption of any asbestos-containing materials that would be abated during a renovation project. When an assumption of asbestos-containing material is done in a non-public building, all of the above must be completed except for the DSHS Inspector and Laboratory License Numbers (not required). 10) Include in this section the demolition and renovation techniques to be used and a description ofthe areas and types of facility components, wliich will be affected by this work. The specific type of asbestos-containing building material that will be abated must be listed. Example: Vinyl asbestos-containing floor tiles to be removed by wet methods recommended by the Resilient Floor Covering Institute. 11) Describe the work practices and engineering controls selected to ensure compliance with the requirements of the regulations, including both the asbestos removal and waste-handling emission control techniques. Example: describe a glove-bag procedure, including the use of a HEPA vacuum. Work practices that vary from the provisions of TAHPR, §295.60 must be clearly described in this section. ] 2) If asbestos is present, the chart must be completed. 1f no asbestos is present (a.s revealed by the survey), check the box provided. Category I non-friable ACBM includes floor tile, when removed intact, floor tile mastic, gaskets, and roofing material. Category II non-friable AGBM includes transite siding. Use the appropriate row to designaie whether the "Category I or Category 11 non-friable ACBM to be removed" is located on the interior or exterior of the building. IfCategory 1 or fl materials are to be sanded, gound, abraded, crumbled, pulverized, reduced to powder, or have the potential to become friable because of the abatement procedures, then list them with RACM. " Category I and Il NOT removed" would be listed for demolitions or for enclosure or encapsulation. (Transite does not remain Category 11 during demolition and must be removed prior to demolition). "RACM NOT removed" would be listed for enclosure or encapsulation or in the event of a demolition under very specific conditions (such as the demolition of a structurally unsound building). RACM 0ff-Faciliry Component (material that is not attached to the facility) shall only be measured in cubic feet or cubic meters. All other material must be measured in linear feet or meters (pipes) or in square feet or meters (surface material). If an abatement will be performed in a portico, or a HVAC system that conditions the inside of a public building, list the amount as "Interior Category I non-friable removed, Interior Category II non-friable removed, or RACM to be removed", depending on the type of ACBM that will be removed. The amounts listed should always reflect the TOTAL amount removed during the project. 13) Provide all information for the waste transporter. The TAHPR reyuires that a DSHS Licensed Transporter transport ACBM from the public building removal site to the waste disposal site. Provide the license number ifthe project is a public building. tf you are performing a demolition without ACBM you still need to list who will be transporting the waste from the project site. If two waste transporters are utilized, one to transport to a holding site aiid one to transport from tlie holdiiig site to the waste disposal site, list the first transporter on the notification. However, the waste manifest must contain infonnation for both transporten. 14) Provide all information for the waste disposal site. State regulations require that all waste disposal sites be permitted by the Teaas Commission on Environmental Quality (TCEQ), including disposal sites located at industrial facilities. Provide the permit number. UUU2ii